Six Simple Tips for Rifle Sight-In

Six Simple Tips for Rifle Sight-In

written by Ray Sasser

For most hunters, getting a shot at a deer or other big-game animal is a difficult chore that requires a lot of time, money and hard work. While you cannot control the movements of a wild game animal, you must make certain that your rifle shoots where it is aimed. Here are six simple rifle sight-in tips from Jim Ridings, owner of Outback Sportsman shooting range, custom ammo and rifle business near Dallas, Texas. Ridings has sighted in literally thousands of rifles in every popular caliber.

Sighting in a rifle

1) Don't rely on bore-sighting for rifle accuracy. Many gunsmiths use a mechanical device called a collimator to approximately align the crosshairs with the rifle bore. This is usually done when a scope is mounted on the rifle. The key word here is "approximately." Bore-sighting can be very precise; it will likely be precise enough to place the bullet somewhere on the paper target at 25 yards.

One memorable Saturday morning prior to the opening of deer season, Ridings had eight hunters fire new bore-sighted rifles on his range. The most accurate of the eight rifles placed the bullet within a foot of the bull's-eye at 25 yards. To be certain where your rifle shoots, you must fire at paper targets from a solid rest.

2) Fire your first shots at 25 yards. After sighting-in virtually every caliber and bullet weight commonly used in big-game hunting, Ridings has found that most modern calibers sighted-in to shoot 3/10 of an inch low at 25 yards are about 2.5 inches high at 100 yards.

Since most deer hunters sight-in a little high at 100 yards, the 25-yard rule of thumb is a good one to remember. Because of image size and ease of precision aiming at short distances, bullet placement is much easier at 25 yards than at 100 yards.

3) Ridings uses sandbags to hold the rifle absolutely steady when sighting-in. He then fires his first shot. He leaves the rifle sandbagged in position. To save ammunition, Ridings does not sight-in in typical fashion by adjusting the crosshairs to move the point of aim toward the bull's-eye. Instead, with the rifle still solidly on the sandbags, he adjusts the scope so the crosshairs are centered on the bullet hole he just punched in the target. That means the scope is now lined up with the bore.

The second shot should be pretty near the bull's-eye. A third shot may be required to fine-tune where the bullet strikes at 25 yards. You should then fire the rifle at 100 yards. For that matter, you should also fire the rifle at the farthest distance you expect to shoot at game, just to see where it hits at longer ranges.

From a practical standpoint, long-distance shooting at paper targets emphasizes human error in precision shooting. Those 1-inch, 100-yard groups you're so proud of open up considerably at 300 yards.

4) If your rifle gets out of whack while in the field, you can bore-sight it yourself. That's assuming you shoot a bolt-action rifle. Set up a target at 25 yards. Remove the rifle bolt and set the rifle up on sandbags in such a position that you can look through the bore and have it centered on the target. Then, without moving the rifle, adjust the crosshairs until they're likewise centered on the target. Again, fire the rifle to make certain of the alignment.

5) When you fire repeated shots at the same target, it's difficult to remember the sequence in which the shots were fired. Keep an identical target beside you on the shooting bench. As you fire each shot, locate the bullet strike on the downrange target. With a pen or pencil, locate and number each corresponding bullet strike on your shooting bench target.

Logging each shot in sequence makes it easier to determine the effectiveness of scope adjustments. If you flinch and shoot a "flyer," it's easier to identify its downrange location if previous shots were logged in sequence.

6) Use the same ammunition for hunting that you use when sighting-in. Not only does the brand of ammo make a difference in rifle performance, bullet weights and bullet designs within the same brand make a difference.

Ridings has found that premium factory ammunition outperforms standard ammo in most rifles. Premium ammo costs about three times as much as standard loads, but it approaches hand-loaded ammo in performance.

Fine-tuning loads to suit your particular rifle is the best method of improving accuracy. If you lack the time or patience for reloading, gunsmiths such as Ridings will work up loads for you and custom load your ammunition. Custom ammunition costs slightly more than premium factory ammo. Compared to other hunting expenses, however, the price of ammunition is insignificant.

Comments for Six Simple Tips for Rifle Sight-In


Name: Larry Gaines
Time: Monday, October 22, 2012

That's pretty close to the steps I have been using for my 7mm mag. I hunt with a 139 grain hornady zeroed at 40 yards. If it is dead on it will be slightly high and 100 and slightly low at 200. It performs extremely well.

Name: Paul Bottino
Time: Saturday, November 10, 2012

I would like to print this out, I am doing exactly this with my new AR scope.

Leave a comment





Captcha